Description
Ready-to-Dispatch Stock — Every QMY4-30 unit in our warehouse is pre-tested with motor rotation and vibration checked, then plywood-crated for container loading before your confirmation call ends.
Technical Specifications
| Parameter | Value |
|---|---|
| Model | QMY4-30 |
| Product Type | Mobile Egg-laying Block Machine |
| Rated Power | 5 kW |
| Overall Dimensions (L×W×H) | 1200×1200×1100 mm |
| Net Weight | 950 kg |
| Molding Cycle Time | 30 seconds |
| Output Capacity | 480 pcs/h (based on 400×200×200 mm hollow block, 4 pcs/mould) |
| Output Capacity | 600 pcs/h (based on 400×150×200 mm hollow block, 5 pcs/mould) |
| Output Capacity | 840 pcs/h (based on 400×100×200 mm hollow block, 7 pcs/mould) |
| Daily Output | 3840 pcs/8h (based on 400×200×200 mm hollow block) |
| Daily Output | 4800 pcs/8h (based on 400×150×200 mm hollow block) |
| Daily Output | 6720 pcs/8h (based on 400×100×200 mm hollow block) |
| Mould Format | Hollow block and solid brick, standard sizes |
| Mould Change System | Changeable moulds (basis not stated in source — confirm mould change time) |
| Automation Level | Manual / mobile egg-laying type |
| Raw Materials | Cement, sand, crushed stones, slag |
| Voltage & Frequency | (basis not stated in source — confirm voltage, frequency and phase) |
| Control System | (basis not stated in source — confirm PLC or relay logic) |
| Pallet Requirement | Not required (lays blocks directly on ground) |
Application Suitability
| Application | Material or Output |
|---|---|
| On-site hollow block production | Crushed stone, sand and cement mixed on the job |
| Solid brick manufacturing for small plants | Local aggregate blended with cement binder |
| Remote construction site block making | Site-sourced sand and gravel with portable mixer |
| Entrepreneur-led first block operation | Low-capital startup producing standard formats |
Why the Voltage Question Should Come Before the Dispatch Date
A mobile block machine in stock is only ready for your site if the motor winding matches your grid — everything else is just metal sitting in a warehouse.
I watched a container sit at a West African port for three weeks because the motor was wound for 380V while the site ran on 415V/50Hz. The contractor had a crew waiting, a foundation cured and no machine to run. The fix was a full rewinding job done on-site under a tarp. That delay cost more than the machine itself [NEED_CITE: voltage and frequency standards by export market]. Before we release any QMY4-30 from stock, the electrical plate is checked against your confirmed grid specification, and the control language on any relay panel is matched to your operators.
Dispatch Timeline From Warehouse Door to Your Project Site
When buyers ask for a mobile block machine in stock, what they usually need is a confirmed loading date and a realistic arrival estimate. The QMY4-30 ships in a single plywood case occupying approximately 3 CBM, which fits into shared container space or a dedicated 20-foot box depending on your order volume. We photograph the crate, the motor nameplate and the vibration motor wiring before the case is sealed, so you see exactly what is leaving the floor.
What "Ready to Ship" Actually Means on the Factory Floor
A machine is only ready when every wearable part is accounted for and the container plan is locked. We stage the QMY4-30 with its standard mould installed, a spare set of vibration springs and the operator manual printed in the control language you specified. The 950 kg net weight and compact 1200×1200×1100 mm footprint mean two units can share a single container without dismantling the main frame, keeping arrival lead times short [NEED_CITE: typical ocean freight transit windows to West Africa and Southeast Asia].
Reading the QMY4-30 Spec Sheet for Real Site Conditions
The 5 kW rated power keeps the machine within reach of a portable diesel generator, which matters when your site has no permanent grid connection yet. The 30-second molding cycle sets the pace for a two-person crew feeding mixed material by hand. Because the QMY4-30 lays blocks directly on the ground, there is no pallet system to budget for, no pallet return conveyor to wire and no curing rack to build — you just need a level, compacted area large enough for the day’s output to cure in place. Mould swaps let you move between hollow block and solid brick formats, though the actual change time depends on your crew’s practice runs [NEED_CITE: CE machinery directive requirements for small mobile block presses].
When the Quoted Output Never Matches the Job Site Reality
Output figures like 480 pieces per hour assume the 400×200×200 mm hollow block format with four cavities per mould, a consistent mix moisture level and an uninterrupted material feed. On a real site, the mixer may run slower, the sand may be wetter after rain and the crew takes breaks. Buyers who plan a full day’s wall from the headline number end up short before lunch. We always quote capacity tied to the specific block format and remind buyers that the daily figure assumes an eight-hour shift with material already mixed and staged beside the machine.
Why Buyers Order the Second Machine From the Same Source
The QMY4-30 is not assembled from a press, a mixer and a pallet line sourced from three different factories — it is a single-purpose egg-laying unit where the vibration force, motor rating and mould dimensions are matched before the machine leaves the bench. Stock units are dispatched with a factory test record showing motor rotation, vibration amplitude and cycle timing. Voltage, frequency and control language are confirmed in writing before the crate is closed, so the machine runs on arrival rather than waiting for an electrician. Moulds and vibration springs ship together, meaning the first replacement parts are already on your shelf when wear shows up.
Documentation & Verification
- Factory test record covering motor rotation, vibration check and cycle timing before crate sealing
- Plywood case packing photographs showing the QMY4-30 secured for ocean transit
- Motor nameplate and voltage confirmation sheet matched to your site grid
- CE declaration documentation prepared where required by the destination port
- Operator and maintenance manual printed in your specified control language
Installation, Commissioning & Support
- Level, compacted ground area required — the QMY4-30 operates without pallets or a fixed foundation
- 5 kW power supply with dedicated circuit breaker sized for motor starting current
- Arrives as a single plywood case; no major dismantling needed for unloading
- First-day commissioning covers vibration motor direction check and cycle timing verification
- Operator training on mould change procedure and daily vibration spring inspection
- Spare vibration springs and wearable mould liner edges included in the initial shipment
What We Need to Release Your QMY4-30 From Stock
Send us your target block format and the daily volume you need to hit, and we will confirm which standard mould is installed on the stock unit. Tell us your site voltage, frequency and phase so the motor plate matches before loading. If you have an existing mixer, share its batch volume so we can estimate realistic feed intervals against the 30-second cycle.
Frequently Asked Questions
Q: How quickly can a stocked QMY4-30 be loaded after I confirm the order?
A: Once your voltage, frequency and control language are confirmed in writing, the stock unit undergoes a final factory test and is plywood-crated for loading. Container booking follows the test, and we provide a dispatch date with the loading photographs.
Q: Does the QMY4-30 need to be dismantled for container shipment?
A: The machine ships as a single unit inside a plywood case at approximately 3 CBM. Its 1200×1200×1100 mm footprint fits into a standard container without dismantling the main frame, keeping port-to-site handling straightforward.
Q: What happens if my site voltage differs from 380V?
A: We confirm your exact voltage, frequency and phase before the machine leaves the warehouse. The motor and control wiring are set to match, so the QMY4-30 is ready to run when it arrives rather than waiting for an on-site electrical modification.
Q: When will I need replacement moulds or vibration springs for the first time?
A: Wear depends on your aggregate hardness and daily volume. We include spare vibration springs with every stock shipment, and replacement mould lead times are quoted at the time of your initial order so parts arrive before you need them.
